Search results

Greg emailed me today that hopefully adjustable upper control arms may be ready by the end of the month.

Waiting for GRP to make them already. Greg, when can we expect some adjustable ones to be made?

No

Does anyone think the extended ones will benefit when tracking the car over the smaller ones?

Has anyone installed the extended paddle shifters and what do you like better about having the extended ones?

JUBU vented louvre already solves this problem after you remove the rear windshield

Tried a search and can't find this Snowtech intercooler and cooling reservoir for sale online. Where can I buy these parts? Does anyone know if anyone else makes this or will make these parts other than Snowtech?

Alot of good information for the dealer when I bring it in to diagnose the issue. I just wanted to confirm that it's not the aftermarket parts that caused the issue. Will update everyone once they figure things out, thank you!

Of course I know there will be more heat, but I want some cooling options because it is mostly a track day car and I don't want any more issues. JUBU has some parts and wanted to know if anyone has installed them?

Will this new lid help reduce the increased heat temperatures that will be caused by installing the JB4 tune with MAP 2 on the supercharger? Is the $825 the pre order price? How long is the pre order price valid until? What will the regular price be afterwards?

What's the point of installing the JB4 if you can't run MAP 2 or 3 for a track event because of over heating? Isn't it better to install a piggy back that will unleash more power by getting the rev limiter past the 6,800 RPM wall? What are the best fixes available that can be installed to keep...

Just to summerize: My 02 sensor fault code only appeared after the Milltek valve controller was installed, as well as the 3rd cat delete. We cleared it multiple times and it always came back. The car went into limp mode once after an autocross event, but after shutting off car and restarting, it...

What are the multiple issues you are referring to with the valve motor? Did you get the same code and go into this limp mode as well? Did you have any aftermarket parts installed? How long does it take to get a new valve motorbeing that my dealership is in New York?

My 02 sensor fault was in Bank 2. Please explain what happened to you and the what resolved the issue in detail so I can reference this to the dealer when I bring in my car next week, thank you

SM-10RS Please in 19s

Done and it's fine so the valve motor must have went bad.

APEX meets and exceeds JWL with 3rd party testing. Anxiously awaiting 19s in the lightest weight, multiple styles and width choices to select and mount a variety of slick sizes that will take track days to the next level. Any updates?

Are you thinking you will get a minimum of 7 extra horse power? What will pricing be around? Will this affect warranty?

Fuse was not blown The Version 1 valve controller was far away. It was the wire that goes to valve motor that was fried. Milltek sent Vesrsion 2 and codes still there so I went back to stock setup and still a code and won't rev past 4k

Version 1 will burn harness wire at the valve moror unless you heat wrap it, which was not in the installation instructions. So Wrap it because you will eventually have it fry and fail. Version 2 is the way to go, but after the installation there is still a fault code and car can't rev above...

Will this allow for headers to work properly without code issues?

Will we be able to install headers now and will this JB4 tune help not throw any codes. Is anyone going to do this mod and give us some feedback?

If tracking and you want to push behind someone you must use windshield PPF. I had 3 big rocks that would have destroyed my windshield the last 2 track days. Best $500 spent because you’d have to get a new windshield anyway.

Car is at the garage now waiting on new Milltek harness since the old one got melted tracking and a new one will be heat wrapped. The factory has holes with grommets, but they need to be enlarged and left open under the back of the trunk lid because water doesn’t drain easily because the holes...

The top louvre sticks out over the bottom ones slightly, but it still won’t prevent water from splashing into engine bay. I opened the trunk after it rained and water splashed everywhere. You have to drill bigger holes to let water drain on either side and middle under trunk plastic to let that...

My dealer said it would void my warranty

Did you find out what the issue was and has it been resolved? I was told by Greg to use heat wrap so I don’t have any issues again when I reinstall everything

I think you meant to post this on the Ohlins thread.

Did you get your car yet? Did you or anyone else order them because we would love some track time feedback once installed?

That’s like saying I can’t wait to make love to my lady, but I’ll put a bag over her head so it’ll be okay. I don’t even have to drive my cars because I can enjoy just looking at them as works of sculpted art. But I’m also fortunate that I can drive them hard! To each his own

Looks fantastic and the color is perfect! Where did you send them to get that done? Are they repainted or powder coated? How long was the turn around? How much did it cost to get the color change without the shipping? Waiting for pictures after you mount them

Which engine oil and weight would be best suited for track days after your analysis?